Please read the following instructions carefully. If you have any questions, please contact the Managing Editor at

[email protected] or [email protected]


Title page

1.1. Title : The title should be relatively short but informative. 
1.2. Name(s) of author(s): A list of all authors of the paper should be prepared. It will contain full first name, initial(s) for middle name(s) and full last name.
1.3. Name and address of workplace(s): Authors’ affiliations should be indicated in this section. 
1.4. Personal e-mail address(es): At least one e-mail address is needed. It will be used as the corresponding author’s email address in all contacts with the authors.

2. Abstract

An abstract must accompany every article. It should be a brief summary of the significant items of the main paper. It should be informative and not only present the general scope of the paper but also indicate the main results and conclusions. An abstract should not normally exceed 250 words.

3. Keywords

List of all keywords proposed by the authors, separated by commas. Up to 5 key terms can be selected. We would suggest avoid repeating the title.

4. Introduction

Present the subject of paper clearly, indicate the scope of the subject, and present the goals of paper, novelty of research work and finally the organization of paper.

5. Materials and Methods

Animals and chemicals should be described in the first two paragraphs. The permission from animal ethical committee should be mentioned. The source of chemicals and drugs may be given, if necessary. The basis of dosage calculation (free form or salt used) should be indicated. Sex, strain and approximate weight of animals should be given (e.g.: “Male Wistar rats; 100–230 g...?) and housing and feeding conditions briefly described. Dosage schedules need not be mentioned in “Materials and Methods? if easily seen from graphs or tables. The route of administration (po, iv, ip, icv), solvent etc. should be indicated. Newly introduced techniques should be described in detail to allow easy repetition. Any modification should be mentioned briefly, with proper references. Techniques which have been previously described should be mentioned in brief only, with proper references, unless they were published in sources that are not easily accessible.
Experimental Part: It should be written in sufficient detail to enable others to repeat the authors’ work. 
Computational Part: In theoretical papers, technical details such as the computational methods, and models applied or newly developed models should be presented in an appropriately named section. Sufficient detail should be provided to enable readers to reproduce the calculations.

6. Results and Discussion

It may be combined or kept separate and may be further divided into subsections. This section should not contain technical details. Abbreviations and acronyms should be used sparingly and consistently. Where they first appear in the text, they should be defined; authors may also explain large numbers of abbreviations and acronyms in a footnote on the first page.

7. Conclusion

It should be representing the summary of the important findings.

Information concerning research grant support should appear in a separate Acknowledgements section at the end of the paper, not in a footnote.

Authors should use tables only to achieve concise presentation or where the information cannot be given satisfactorily in other ways. Tables should be numbered consecutively using Arabic numerals and should be in the text itself at appropriate place not at the end or as separate attachment. Each table should have an explanatory caption which should be as concise as possible.

Authors may use line diagrams and photographs to illustrate these from their text. The figures should be clear, easy to read and of good quality. Styles and fonts should match those in the main body of the article. Lettering and lines should be of uniform density and the lines unbroken. Axis labels should be in bold face. Units should be placed next to variables in parentheses. All figures must be in the text itself appropriate place not at the end or as separate attachment..

8. References

The references should be cited in the text in large brackets not in superscript or subscript. A complete reference should comprise the following:

An article in a journal
Graiver D, Dacomba R, Khawaji M, Jaros A, Berglund K, et al. (2012) Steel-Corrosion Inhibitors Derived from Soybean Oil. J Am Oil Chem Soc 89:1895-1903.

A book
C.N.Rao, A. Muller, A. K. Cheetham; The Chemistry on Nanomaterials. Synthesis, Properties and Applications, Wiley-Vch, Weinheim, 2004.
A part/chapter book
C.K. Clenshaw, K. Lord, In: B.K. P. Scaife (Ed.), Studies in Numerical Analysis (Academic Press, London and New York, 1974) 95.

A conference proceeding
A. Kaczanowski, K. Malarz, K. Kulakowski, In: T.E. Simos (Ed.), International Conference of Computational Methods in Science and Engineering, 12-16 Sep. 2003, Kastoria, Greece (World Scientific, Singapore 2003) 258.

 A thesis
A.J. Agutter, PhD thesis, Edinburgh University (Edinburgh, UK, 1995).

An article in a newspaper
A. Sherwin, The Times, 13 Jul. 2007, 1.

Patents:  A. B. Inventor1, C. D. Inventor2, (Holder), Country Code and patent number (registration year).

Submission formats
Manuscripts should be submitted in the MS Word (97 or higher).

Submission of manuscript
The authors must submit their manuscript to or send as an email attachment to the Editorial office at [email protected] or [email protected] 

Manuscript Type

Article Processing Charges




Research and Review Articles




Special Issue Article




Short Communication,Commentary Articles, Case reports, etc.,




The articles published in any of the Journal of PRL are open access. This effectively removes the barriers for timely distribution of the articles and ensures that they can be read by as many people as possible. Publication fee is required to cover the cost of the publication and other expenses incurred. Payment can be made by credit card, bank transfer, money order or check. Instruction for payment is sent during publication process.



We will look forward to the submission of your next manuscripts

Recommended Conferences

  • 4thInternational Conference on Glycobiology and Glycochemistry
    May 16-17, Singapore
  • 3rd International Conference on Food Chemistry & Nutrition
    May 16-18, Montreal, Canada
  • 6th International Conference and Exhibition on Materials Science and Chemistry
    May 17-18, Rome, Italy
  • 17th International Conference on Industrial Chemistry and Water Treatment
    May 21-22, New York, USA
Flyer image

Abstracted/Indexed in

  • Chemical Abstracts Service (CAS)
  • Open J Gate
  • Genamics JournalSeek
  • Directory of Research Journal Indexing (DRJI)
  • Publons
  • International Committee of Medical Journal Editors (ICMJE)
  • Serials Union Catalogue (SUNCAT)
  • Geneva Foundation for Medical Education and Research